Submission Details
TerraRaptor的SuperPi - 1M成绩 - 极限联盟
34sec 239ms 和 AMD Athlon XP 2600+ (Barton) 在 2905.6MHz
排名位置
n/a
全球排名
1st
Athlon XP 2600+ (Barton) 排名:
Points earned for overclocker league
-
全球分数(UGP)
Not TerraRaptor's best submission
-
硬件分数(UHP)
1st 使用 Athlon XP 2600+ (Barton)
50.0 积分
Points earned for team league
-
全球战队能量分 (GTPP) Not Team Russia's best submission
0.0 积分
-
硬件战队能量分(HTPP) 1st 战队使用Athlon XP 2600+ (Barton)
20.3 积分
硬件细节
CPU细节
- 型号: AMD Athlon XP 2600+ (Barton) 'Barton'
- 散热: Single Stage Phase Change
- Cores: 2,905.62MHz(+52.93%)
内存细节
- 类别 DDR SD-RAM
显卡细节
- 速度:: MHz / MHz ()
主板细节
- 厂商: ASUS
- 型号: A7N8X-E Deluxe
- 散热: Air (Stock)
- 芯片组: nForce2 Ultra 400
-
近期的评论
TerraRaptor 评价他自己的分数:
Seems the board is now capable of running 267 mhz tight (which is likely the limit of my RAM) but I've almost killed my AXP-M 2500+ during research (now only 64kb of L2) so to get good result I need to find good enough processor with lower multi. Vcpu 2.175v, Vnb 2.05v, Vdimm 3.8v. Trats bios 1013-1T.
Alpi 说:
Inane work on this board ! 267mhz mem with tight subs are pretty much lead You to max out every chip You just want ! Very nice, very nice ! I'm curious of Your future work, keep pushing ! ;)
GRIFF 说:
Awesome work. Voltmod of MCP Is need?
Mr.Scott 说:
Nice. You made a mediocre board a superstar. It's awesome.
d0minat0r 说:
well done!
macsbeach98 说:
Nice work Good Show
Over the years I have had 2 of these boards and never tried them the lack of 12v CPU power put me off will have to try one oneday.
kicsipapucs 说:
Wow, that's awesome!
TerraRaptor 说:
Thanks all. I will recheck some of cpus with NF7v2 in next few weeks (NF7 is also strong on fsb and validates 275MHz) to see if Asus board is not limiting me on total cpu clock and will later share my trick to break 260 Mhz with A7N8X.
The resistor I use gives the lowest of 2.05v (that is combo of 2 resistors actually) - going to 2.15v worsens stabilty. I think voltmod is necessary but 2.05v may be unnecessary.
I.nfraR.ed 说:
What helps me for stability is modded 3.3V PSU rail and HAL set to "Standard PC". Of course modded bios is a must. Most of my boards don't scale much above 2-2.1V vdd and very often higher voltage hinders the stability. I even have one NF7 that can't do 250+ stable if the vdd is higher than 1.8V.
Interested to see if you know something else
PS: Try a locked XP 2500+ if you have one. It's cool to beat unlocked CPUs, just because you run much higher FSB
Edit: Ah, you have one.
TerraRaptor 说:
I broke the core of the best one this summer, other 2500+ won't go high enough.
Actually I can share it here - bus 0 dev 0 func 3 offsets 66 and 68 - set both to C7 or 07 (haven't yet bothered to identify the exact bit - although should be simple - just one of those 2 bits in 11xx0111 sequence with xxxx0xxx being mandatory). Don't know what it is exactly - was bruteforcing it in wpcredit - with zero impact on performance.
I.nfraR.ed 说:
Thanks. Have you checked if those are set differently on other boards?
I'm still trying to finish the ZenStates release and then will probably play with K7 and K8 a little.
I have DFI Ultra-B, NF7, AN7 - could check on all of them, but it requires some free time.
leeghoofd 说:
respect bro
Tzk 说:
Very nice score, well done! Especially on this board... I'm curious what your "trick" to reach 260Mhz+ on the A7N8X is... ;)
Sparks.nl 说:
Very nice score. My board back then didn’t even come close...
请登录或注册后才能评论