Submission Details
Le score de TerraRaptor sur SuperPi - 1M - Extreme League
34sec 239ms avec AMD Athlon XP 2600+ (Barton) à 2905.6MHz
Position dans le classement
n/a
Classement général:
1st
Athlon XP 2600+ (Barton) classement:
1st sur un total de 77
Points earned for overclocker league
-
Points Global (UGP)
Not TerraRaptor's best submission
-
Points Hardware (UHP)
1st utilisant Athlon XP 2600+ (Barton)
50.0 Points
Points earned for team league
-
Points Global Team Power (GTPP) Not Team Russia's best submission
0.0 Points
-
Points Hardware Team Power (HTPP) 1st en équipe utilisant Athlon XP 2600+ (Barton)
20.3 Points
Détails matériel
Détails Processeur
- Modèle: AMD Athlon XP 2600+ (Barton) 'Barton'
- Refroidissement: Single Stage Phase Change
- Cores: 2 905,62MHz(+52.93%)
Détails mémoire
- Type: DDR SD-RAM
Détails carte graphique
- Fréquence: MHz / MHz (Stock)
Détails carte mère
- Fabricant: ASUS
- Modèle: A7N8X-E Deluxe
- Refroidissement: Air (Stock)
- Chipset: nForce2 Ultra 400
-
Commentaires récents
TerraRaptor a commenté son propre score:
Seems the board is now capable of running 267 mhz tight (which is likely the limit of my RAM) but I've almost killed my AXP-M 2500+ during research (now only 64kb of L2) so to get good result I need to find good enough processor with lower multi. Vcpu 2.175v, Vnb 2.05v, Vdimm 3.8v. Trats bios 1013-1T.
Alpi dit :
Inane work on this board ! 267mhz mem with tight subs are pretty much lead You to max out every chip You just want ! Very nice, very nice ! I'm curious of Your future work, keep pushing ! ;)
GRIFF dit :
Awesome work. Voltmod of MCP Is need?
Mr.Scott dit :
Nice. You made a mediocre board a superstar. It's awesome.
d0minat0r dit :
well done!
macsbeach98 dit :
Nice work Good Show
Over the years I have had 2 of these boards and never tried them the lack of 12v CPU power put me off will have to try one oneday.
kicsipapucs dit :
Wow, that's awesome!
TerraRaptor dit :
Thanks all. I will recheck some of cpus with NF7v2 in next few weeks (NF7 is also strong on fsb and validates 275MHz) to see if Asus board is not limiting me on total cpu clock and will later share my trick to break 260 Mhz with A7N8X.
The resistor I use gives the lowest of 2.05v (that is combo of 2 resistors actually) - going to 2.15v worsens stabilty. I think voltmod is necessary but 2.05v may be unnecessary.
I.nfraR.ed dit :
What helps me for stability is modded 3.3V PSU rail and HAL set to "Standard PC". Of course modded bios is a must. Most of my boards don't scale much above 2-2.1V vdd and very often higher voltage hinders the stability. I even have one NF7 that can't do 250+ stable if the vdd is higher than 1.8V.
Interested to see if you know something else
PS: Try a locked XP 2500+ if you have one. It's cool to beat unlocked CPUs, just because you run much higher FSB
Edit: Ah, you have one.
TerraRaptor dit :
I broke the core of the best one this summer, other 2500+ won't go high enough.
Actually I can share it here - bus 0 dev 0 func 3 offsets 66 and 68 - set both to C7 or 07 (haven't yet bothered to identify the exact bit - although should be simple - just one of those 2 bits in 11xx0111 sequence with xxxx0xxx being mandatory). Don't know what it is exactly - was bruteforcing it in wpcredit - with zero impact on performance.
I.nfraR.ed dit :
Thanks. Have you checked if those are set differently on other boards?
I'm still trying to finish the ZenStates release and then will probably play with K7 and K8 a little.
I have DFI Ultra-B, NF7, AN7 - could check on all of them, but it requires some free time.
leeghoofd dit :
respect bro
Tzk dit :
Very nice score, well done! Especially on this board... I'm curious what your "trick" to reach 260Mhz+ on the A7N8X is... ;)
Sparks.nl dit :
Very nice score. My board back then didn’t even come close...
Veuillez vous identifier ou enregister pour commenter