Submission Details
SteveRo`s PCMark05 (alpha) score - Extreme League
22688 marks with AMD Sempron 145 at 4928MHz
Ranking position
n/a
Global 1x CPU rank:
4th
Sempron 145 rank:
4th out of 60
Points earned for overclocker league
-
Global Points
Not SteveRo's best submission
-
Hardware Points
4th using Sempron 145
Points earned for team league
-
Global Team Power Points (GTPP) Not XtremeSystems's best submission
0.0 Points
-
Hardware Team Power Points (HTPP) 4th in team using Sempron 145
0.0 Points
Media gallery
- Verification URL, image, checksum
- http://3dmark.com/pcm05/3152721
Hardware details
CPU details
- Model: AMD Sempron 145 'Sargas' (1 cores active)
- Cooling: Cascade Phase Change
- Cores: 4,928MHz(+76.00%)
Memory details
- Manufacturer: Crucial
- Product: 1066c5
- Cooling: Air (Stock)
- Type: DDR2 SDRAM
- Speed: @ 704MHz
- Timings: 4-3-3-9-12
VGA details
- Model: Radeon HD 7970 (Tahiti) AMD
- Cooling: Air (Stock)
- Speed: 1,240MHz (+34.05%) / 1,750MHz (+27.27%)
Mainboard details
- Manufacturer: GIGABYTE
- Model: GA-MA790X-UD4P
- Cooling: Air (Stock)
- Chipset: 790X
-
Recent Comments
SteveRo commented on his own score:
Well we all have good days and bad days. Today was a bad day for me :( Going from cascade to ln2 only got me +2 increase in bus and about 20 marks - oh well. :( Anyone have any ideas please let me know!! Thanks.
Gluvocio says:
perhaps you have a wall on MCH or NB or CPU
Have you tested it with different cpu ?
What's your mainboard FSB edge ?
Wat's your memory edge on that main ?
You did much job for small benefits... Pcmark on LN2 should make a person very busy doing it.
Mafio says:
third place is still good, congrats.
SteveRo says:
^^ Denis - thanks, all good ideas - yes, I need to isolate the problem - could be the board or the cpu I guess. I do have other cpus I can use to test the board.
Thanks Mafio - was already at #3 trying to improve!
MrPaco says:
May just be the chip is a slacker . Do you have another 145 to try in that same set up to test?
But as always, still a great run...
BeepBeep2 says:
I think HT Ref. is really limited to the individual motherboard/chip and there isn't much to do for it.
You can try to put HTT and CPU_NB voltage through the roof but I don't know if that will help.
I really like the board though, I had one of those, back in 2010 and sold it to Gautam...is that the one I had?
Don_Dan says:
I don't think this is your board Beep!
BeepBeep2 says:
I wouldn't either
Might as well ask!
SteveRo says:
Beep - na - i bot this boad new. at sompoint i will try a different chip in it - see if the bus spped wall is the board or the chip
I killed my last sempron with too much cpu/nb - would like to not do that again!!
I.M.O.G. says:
My chip ran out of gas around there I think Steve. I thought it was the mainboard, but then I switched to a board that can do known higher FSB, and it didn't go any further.
Don't feel bad about killing Sempy's. They are cheap and easily replaced... Reminds the chips who is boss.
Good job.
Please log in or register to comment.