Submission Details
SteveRo`s PCMark05 (alpha) Ergebnis - Extreme League
22688 marks mit AMD Sempron 145 at 4928MHz
Ranglisten Position
n.a.
Globaler 1x CPU Rang:
4th
Sempron 145 Rang:
4th von 60
Points earned for overclocker league
-
Globale Punkte (UGP)
Not SteveRo's best submission
-
Hardware Punkte (UHP)
4th mit Sempron 145
Points earned for team league
-
Globale Team Power Punkte (GTPP) Not XtremeSystems's best submission
0.0 Punkte
-
Hardware Team Power Punkte (HTPP) 4th Im Team verwendet Sempron 145
0.0 Punkte
Mediengallerie
- Verifikations URL, Bilder, Checksumme
- http://3dmark.com/pcm05/3152721
Hardware Details
CPU Details
- Model: AMD Sempron 145 'Sargas' (1 Kerne aktiv)
- Kühlung: Cascade Phase Change
- Cores: 4.928Mhz(+76.00%)
Arbeitsspeicher Details
- Manufacturer: Crucial
- Produkt: 1066c5
- Kühlung: Air (Stock)
- Typ: DDR2 SDRAM
- Geschwindigkeit: @ 704Mhz
- Timings: 4-3-3-9-12
VGA Details
- Model: Radeon HD 7970 (Tahiti) AMD
- Kühlung: Air (Stock)
- Geschwindigkeit: 1.240Mhz (+34.05%) / 1.750Mhz (+27.27%)
Mainboard Details
- Hersteller: GIGABYTE
- Model: GA-MA790X-UD4P
- Kühlung: Air (Stock)
- Chipsatz: 790X
-
Neueste Kommentare
SteveRo Kommentierte sein eigenes Ergebnis:
Well we all have good days and bad days. Today was a bad day for me :( Going from cascade to ln2 only got me +2 increase in bus and about 20 marks - oh well. :( Anyone have any ideas please let me know!! Thanks.
Gluvocio sagt:
perhaps you have a wall on MCH or NB or CPU
Have you tested it with different cpu ?
What's your mainboard FSB edge ?
Wat's your memory edge on that main ?
You did much job for small benefits... Pcmark on LN2 should make a person very busy doing it.
Mafio sagt:
third place is still good, congrats.
SteveRo sagt:
^^ Denis - thanks, all good ideas - yes, I need to isolate the problem - could be the board or the cpu I guess. I do have other cpus I can use to test the board.
Thanks Mafio - was already at #3 trying to improve!
MrPaco sagt:
May just be the chip is a slacker . Do you have another 145 to try in that same set up to test?
But as always, still a great run...
BeepBeep2 sagt:
I think HT Ref. is really limited to the individual motherboard/chip and there isn't much to do for it.
You can try to put HTT and CPU_NB voltage through the roof but I don't know if that will help.
I really like the board though, I had one of those, back in 2010 and sold it to Gautam...is that the one I had?
Don_Dan sagt:
I don't think this is your board Beep!
BeepBeep2 sagt:
I wouldn't either
Might as well ask!
SteveRo sagt:
Beep - na - i bot this boad new. at sompoint i will try a different chip in it - see if the bus spped wall is the board or the chip
I killed my last sempron with too much cpu/nb - would like to not do that again!!
I.M.O.G. sagt:
My chip ran out of gas around there I think Steve. I thought it was the mainboard, but then I switched to a board that can do known higher FSB, and it didn't go any further.
Don't feel bad about killing Sempy's. They are cheap and easily replaced... Reminds the chips who is boss.
Good job.
Bitte einloggen oder register to comment.