Submission Details
Stelaras的3DMark 99 Max成绩 - 极限联盟
12020 marks 和 ATi Rage Fury MAXX 在 160/172MHz
排名位置
345th
世界纪录排名
58th
全球2x GPU排名:
2nd
Rage Fury MAXX 排名:
Points earned for overclocker league
-
世界纪录分数(UWP)
345th
-
全球分数(UGP)
58th 使用 2 GPU
-
硬件分数(UHP)
2nd 使用 Rage Fury MAXX
Points earned for team league
-
全球战队能量分 (GTPP) Not Hellas Overclocking Team's best submission
0.0 积分
-
硬件战队能量分(HTPP) 2nd 战队使用Rage Fury MAXX
4.7 积分
硬件细节
CPU细节
- 型号: Intel Pentium III EB 1000Mhz (Slot 1) 'Coppermine-256'
- 散热: Liquid Nitrogen
- Cores: 1,350MHz(+35.00%)
-
内存细节
- 类别 RDRAM
显卡细节
- 型号: Rage Fury MAXX (128 Pro) ATi
- 散热: Air (Stock)
- 速度:: 160MHz (+28.00%) / 172MHz (+20.28%)
近期的评论
Stelaras 评价他自己的分数:
Stelaras & Zafiropo - Ati rage Fury MAXX - OSIBS S3-R5 FSB is maxed out at 180Mhz . Cpu is capable for higher clocks . No time for external PLL .
Strunkenbold 说:
Very nice board. Im jealous, would like to have one too.
kotori 说:
Really great work Stelaras-san and Zafiropo-san, I did the my best but didn't reach 12000 3D marks, congrats!
TASOS 说:
Congrats zafiropo and stelaras !!!
Great score.
Stelaras 说:
Thank you both
Considering it's a dual CPU board it did great . I wasn't expecting to max-out the PLL at 180MHz to be honest .
Kotori-san , as i can tell by looking at your score , our runs were pretty close in efficiency . RDRAM doesn't help Pentium-III CPUs and performs close to SD-RAM .
I believe the main reason i got to 12K was because of the CPU . If i had your SH6 board i'm sure i would have scored way higher .
The 1000EB CPU was only at 2.05V & -30C . It was enough for booting , entering windows and running the benches . Totally stable at 180MHz FSB .
Thank you again for your kind words !
Stermy57 说:
Beautiful Board and score. Well done
Stelaras 说:
Thank you Stermy !
Your last run was very strong ! I tried to reach it with the same board (440bx) but couldn't .
I managed to run the rage128 pro card up to 185/205
GRIFF 说:
Nice and particular board. strong and hard work.
Congratulations.
kotori 说:
Zafiropo-san and Stelaras-san thank you for answering, i saw Zafi-san's post in my sub.
In the case of a single CPU I think wprime and hwbot prime is not so much affecting RAM clock and latency, pi and paifast will make a difference.
If dual cups, difficult runs 180mhz FSB in 440BX chip.
About External PLL mod, If P3C-D can fine-tune FSB(1mhz step) on bios or setfsb,
necessarily don't need a external controller, need only 14.138mhz crystal for real time clock and 16mhz or higher crystal and some resistor.
Stelaras 说:
Kotori-san , P3C-D has the ability to use 100 to 180 FSB with 3 Mhz steps . Maybe a different crystal is enough , but i don't know if USB would continue to work properly . I have a turbo-PLL solution almost ready to be used , but zafiropo didn't want to mess with his board!
I can also tell that board is slow . I tried some Spi1M runs but it's very slow compared to the BX chipset , so it just doesn't worth it (except for the benches that are not bandwidth hungry) .
kotori 说:
USB will not work at 16mhz crystal but PS2 is no probrem, in my case, I'm restoring to 14.318mhz only when use USB memory, would be convenient to attach a socket between board and crystal.
请登录或注册后才能评论